Lenze EPM−T9XX Modular system Uživatelský manuál Strana 172
- Strana / 544
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Via system bus (CAN)
Identifier
8
Networking via system bus (CAN)
8.1
8.1.2
L
8.1−2
EDSPM−TXXX−9.0−11/2009
8.1.2 Identifier
The principle of CAN communication is based on a message−oriented data
exchange between a transmitter and many receivers. Therefore, all nodes can
transmit and receive more or less at the same time.
The so−called identifier in the CAN telegram, also called COB−ID (Communication
Object Identifier), controls which node is to receive a transmitted message. In
addition to the addressing, the identifier contains information on the priority of the
message and the type of user data.
The identifier consists of a ’basic identifier’ and the node address of the device to
be approached:
Identifier = Basic identifier + node address
l This node address is set with the coding switch at the module:
– Modular system: At CAN gateway
– Compact system: At each module
l Network management and sync telegram only require the basic identifier.
l The identifiers can also be set individually. ( 8.3−3)
8.1.3 Saving changes
) Note!
l Changes of the baud rate, node address, identifiers for PDOs,
and the transmission mode for PDOs must be saved with
I2003
h
= 1, for being maintained even after switching off the
supply voltage.
l Any changes will become effective only after a Reset Node:
– Switch the supply voltage on again
– Execute NMT command "81
h
" (see chapter "Network
management (NMT)")
– Set I2358
h
= 1
- I/O−System IP20 1
- Contents 10
- 1 Preface 11
- 1.1 The I/O system IP20 13
- How to use this System Manual 16
- Document history 17
- 1.2.3 Document history 17
- 1.3 Legal regulations 19
- Legal regulations 20
- Safety instructions 21
- Technical data 25
- The modular system 100
- The compact system 113
- EPM-T831 1A.10 127
- EPM-T833 1A.10 135
- 02413567 143
- Mechanical installation 147
- Electrical installation 155
- 8.1 Via system bus (CAN) 171
- 8.2 Network management (NMT) 173
- Network management (NMT) 174
- 8.3 Transmitting process data 175
- Transmitting process data 176
- PDO1-TX PDO1-RX 178
- 2. 3. 4 178
- Transmitting parameter data 188
- Telegram structure 188
- Identifier = 1538 190
- Identifier = 1410 190
- 8.6 Node Guarding 195
- Node Guarding 196
- 8.7 Heartbeat 197
- Heartbeat 198
- 8.8 Reset node 199
- 8.9 Monitoring 201
- Monitoring 202
- Digital output monitoring 202
- 8.10 Diagnostics 205
- Diagnostics 206
- Emergency telegram 206
- 8.10.1 Emergency telegram 206
- Status of the digital outputs 208
- Via the index I6401 209
- Via the index I6411 209
- Network via CANopen 211
- Networking via PROFIBUS−DP 255
- Commissioning 283
- 12.1 Important notes 295
- Parameterising analog modules 300
- Parameter data 300
- Diagnostic data 304
- 12.3.2 Diagnostic data 304
- 12.3−11 309
- 12.3−12 310
- 12.3−13 311
- 12.3−16 314
- 12.3−17 315
- 12.3−18 316
- Input data / output data 325
- 2 x 32 bit counter (mode 0) 326
- Encoder (modes 1, 3, and 5) 328
- Counter 0 332
- Counter 1 332
- 12.4−13 333
- 12.4−14 334
- 12.4−15 335
- 12.4−16 336
- 12.4−17 337
- 12.4−18 338
- 12.4−19 339
- 12.4−20 340
- 12.4−21 341
- 12.4−22 342
- 12.4−23 343
- 12.4−24 344
- 12.4−25 345
- 12.4−26 346
- 12.4−27 347
- 12.4−28 348
- 12.4−30 350
- 12.4−31 351
- 12.4−32 352
- 12.4−33 353
- 12.4−34 354
- 12.4−35 355
- 12.4−36 356
- 12.4−37 357
- 12.4−38 358
- 12.4−39 359
- 12.4−40 360
- 12.4−41 361
- 12.4−42 362
- 12.4−43 363
- 12.4−44 364
- 12.4−45 365
- 12.4−46 366
- 12.4−47 367
- 12.4−48 368
- 12.4−49 369
- 12.4−50 370
- 12.4−51 371
- 12.4−52 372
- 12.4−53 373
- 12.4−54 374
- 12.4−55 375
- 12.4−56 376
- Parameterising SSI interface 379
- EDSPM−TXXX−9.0−11/2009 384
- 12.5−11 387
- Encoder (mode 0) 395
- 12.6.3 Encoder (mode 0) 395
- 32 bit counter (mode 1) 397
- 12.6−10 400
- 12.6−11 401
- 12.6−12 402
- 12.6−13 403
- Measuring the period (mode 4) 404
- 12.6−15 405
- 12.8 Loading default setting 409
- · Example: 413
- 13.1−11 423
- 13.1−12 424
- 13.1−14 426
- 13.1−16 428
- 13.1−17 429
- 13.1−18 430
- Gateway Counter 438
- Data to module 438
- Data from module 438
- In3/In6 (DIR) 446
- 13.2−13 447
- 13.2−14 448
- 13.2−15 449
- Counter access 450
- 13.2−17 451
- 13.2−18 452
- 13.2−19 453
- 13.2−20 454
- 13.2−21 455
- 13.2−22 456
- 13.2−23 457
- 13.2−24 458
- 13.2−25 459
- 13.2−26 460
- 13.2−27 461
- 13.2−29 463
- 13.2−30 464
- 13.2−31 465
- 13.2−32 466
- 13.2−33 467
- 13.2−34 468
- 13.2−36 470
- 13.2−37 471
- 13.2−38 472
- 13.2−40 474
- In3/In6 (B) 475
- 13.2−42 476
- 13.2−43 477
- 13.2−44 478
- 13.2−46 480
- 13.2−47 481
- 13.2−48 482
- 13.2−49 483
- 13.2−50 484
- 13.2−52 486
- 13.2−54 488
- 13.2−55 489
- 13.3.1 Parameter data 491
- Gateway SSI-Interface 493
- 13.4.1 Parameter data 495
- Gateway Counter/Dig In 496
- 13.4.3 Encoder (mode 0) 498
- Signal characteristic 503
- 13.4−10 504
- 13.4−11 505
- 13.4−12 506
- 13.4−14 508
- 14.1 Fault messages 511
- Appendix 513
- 10987654321 544
Související produkty a manuály pro Hardware Lenze EPM−T9XX Modular system
Hardware Lenze E82MV752 4Bxxx Uživatelský manuál
(20 stránky)
(20 stránky)
Hardware Lenze EMZ9374IB Uživatelský manuál
(122 stránky)
(122 stránky)
Hardware Lenze EZN3x0060H054 Uživatelský manuál
(58 stránky)
(58 stránky)
Hardware Lenze EPM-H521 Uživatelský manuál
(136 stránky)
(136 stránky)
Hardware Lenze MC−xxx Card Uživatelský manuál
(46 stránky)
(46 stránky)
Hardware Lenze EWS1001 Uživatelský manuál
(12 stránky)
(12 stránky)
Hardware Lenze EWS1003 Uživatelský manuál
(12 stránky)
(12 stránky)
Hardware Lenze E93ZWLX Uživatelský manuál
(77 stránky)
(77 stránky)
Hardware Lenze EMZ2221IB Uživatelský manuál
(58 stránky)
(58 stránky)
Hardware Lenze E82ZMBRB Uživatelský manuál
(58 stránky)
(58 stránky)
Hardware Lenze ECSCMxxx Uživatelský manuál
(375 stránky)
(375 stránky)
Hardware Lenze ECSZZxxxxxx Uživatelský manuál
(68 stránky)
(68 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce