Lenze DSD Uživatelský manuál Strana 350
- Strana / 496
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
11 Drive Dimensioning
11.6 Inverters
350
Lenze · Drive Solution Designer · Manual · DMS 4.2 EN · 12/2013 · TD23
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
11.6.1.4 Overcurrent operation for i700
Temporarily, the power supply modules and axis modules can be operated with output currents
higher than the rated current.
Two utilisation cycles are specified, each with a running time and a recovery time. A running time
must be followed by a recovery time. The current must not exceed the indicated value in the recov-
ery time. All values refer to the rated output current.
• 15-s cycle: pulse utilisation
• 3 s running time with peak current (200 %)
• 12 s recovery time with limited current (66 %)
• 180-s cycle: permanent utilisation
• 60 s running time with peak current (150 %)
• 120 s recovery time with limited current (75 %)
The illustration below shows typical curves of utilisation cycles:
[11-21] Overcurrent capability i700 at 40 °C
15-s cycle: pulse utilisation Equation:
Peak current
Limited current during the recovery time
t
1
Running time with peak current
t
2
Recovery time with limited current
180-s cycle: permanent utilisation Equation:
Peak current
Limited current during the recovery time
t
3
Running time with peak current
t
4
Recovery time with limited current
t
0
100 %
1
0
2
I [%]
N,out
t
2
t
3
t
4
t
1
At
1
Ct
2
⋅+⋅
t
1
t
2
+
--------------------------------
100 %≤
At
3
C4⋅+⋅
t
3
t
4
+
------------------------------
100 %≤
- Drive Solution 1
- Designer 1
- Contents 10
- 1 Notes on usage 11
- 2 About this documentation 14
- Pictograph and signal word! 17
- 3User interface 18
- How to sort the results: 35
- How to filter results: 35
- How to open created notes: 38
- How to delete notes: 38
- 4.3.1 Messages 44
- 4.3.2 Software updates 45
- 4.4 Language 46
- 4.5 Settings 46
- 4.5.3 "Help" tab 47
- 4.5.5 "Units" tab 48
- User data 50
- Registration data: 50
- 4.6 User-specific settings 51
- 4.6.1 User-defined defaults 51
- 5Managing projects 52
- 6 Drive dimensioning tools 55
- 7Applications 100
- Mass calculator ( 405) 109
- Danger! 122
- Pole pair 191
- 8 Motion design 224
- symbol in the toolbar 225
- CINH = 1 271
- 9 Mains and environment 277
- ( 283) 282
- ( 285) 282
- ( 286) 282
- 10.1 Mechanical drive axis 283
- 10.1.1 Lenze gearbox 283
- 10.1.3 Feedback 284
- 10.2 Electrical drive axis 285
- 10.3 Drive concept 286
- 10.3.1 Gearbox features 287
- 10.3.1.1 Axial gearbox 287
- 10.3.1.2 Right-angle gearbox 288
- 10.3.2 Motor properties 289
- 10.3.4 Inverter properties 294
- 10.3.4.1 Frequency inverter 294
- 10.3.4.2 Servo inverters 296
- 11 Drive Dimensioning 308
- 12 Components in the DC bus 361
- 13 Details on Lenze products 377
- 14 Energy efficiency 378
- 15.1 Drawing 386
- Editing functions 389
- 15.2 Results 390
- 15.3 Protocols 391
- 15.3.1 Summarised protocol 391
- 15.3.2 Detailed protocol 391
- 15.3.3 Commissioning data 392
- 15.3.5 Output settings 393
- 15.4.1 Application Tuner 394
- 15.4.3 BlueGreen 394
- ( 378) 395
- 15.6.1 Dynamic reserves 396
- 15.6.2 Stationary reserves 396
- 15.6.3 Speed reserves 397
- 15.6.7 Reserves for gearboxes 399
- 16 Auxiliary means 401
- How to call the calculator: 404
- How to call the DSC: 425
- 17.1 Field weakening 426
- 17.5 Feedback systems 427
- Measured values 430
- 17.16 System disturbances 435
- [17-6] Group drives 436
- 17.19 ATEX for gearbox 437
- 17.21 Emergency-off scenarios 438
- 18.1 Applications 441
- 18.2 Drive system 445
- 18.3 Additional drive element 449
- 18.4 Lenze gearbox 450
- 18.5 Lenze motor 455
- 18.5.6 Motor speed too low 456
- > as winding ratio q 460
- 18.6 Brake 461
- 18.6.3 No brake available 461
- 18.7 Feedback 463
- 18.7.2 No feedback selected 463
- 18.8 Inverters 465
- 18.8.16 Activate VVC control 469
- 18.8.19 Mains choke required 470
- 18.10 Supply module 476
- 18.11 Brake chopper 479
- 18.12 Brake resistor 481
- 18.13 User motor 483
- ( 42) 485
- ( 46) 485
- 20 Glossary 486
- )(('%$& 494
Související produkty a manuály pro Software Lenze DSD
Software Lenze Engineer v2.21 Uživatelský manuál
(312 stránky)
(312 stránky)
(270 stránky)
Software Lenze 8400 motec Uživatelský manuál
(518 stránky)
(518 stránky)
Software Lenze i700 Uživatelský manuál
(338 stránky)
(338 stránky)
Software Lenze 8400 TopLine Uživatelský manuál
(176 stránky)
(176 stránky)
Software Lenze 8400 StateLine Uživatelský manuál
(103 stránky)
(103 stránky)
Software Lenze 8400 HighLine Uživatelský manuál
(157 stránky)
(157 stránky)
Software Lenze 8400 BaseLine C Uživatelský manuál
(342 stránky)
(342 stránky)
Software Lenze 8400 BaseLine D Uživatelský manuál
(260 stránky)
(260 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce