Lenze DDS Target 9300 Servo PLC V8.x Uživatelský manuál stáhnout pdf (Strana 113)

9300 Servo PLC

Appendix

3.5 System error messages

3−107

9300 Servo PLC EN 5.1

3.5.1 Overview of system error messages, error sources and reactions

System error message Possible settings/response

 Lenze setting  setting possible

Available in

No. Display Source Meaning

Code TRIP Message Warning FAIL−QS

Off Drive

PLC

Servo

PLC

ECSxA

x011 OC1 MCTRL Motor cable short circuit   

x012 OC2 MCTRL Motor cable earth fault   

x015 OC5 MCTRL I x t overload   

x016 OC6 MCTRL I

x t overload (C0120)  

x017 OC7 MCTRL I x t warning (C0123) C0604    

x018 OC8 MCTRL I

x t warning (C0127) C0605    

x020 OU MCTRL Overvoltage in the DC bus   

x030 LU MCTRL Undervoltage in the DC bus   

x032 LP1 MCTRL Motor phase failure C0597     

x050 OH MCTRL Heat sink temperature higher than fixed limit

temperature

  

x051 OH1 MCTRL Temperature inside the controller > 90° C  

x053 OH3 MCTRL Motor temperature higher than fixed limit

temperature

C0583    

x054 OH4 MCTRL Heat sink temperature higher than variable

limit temperature (C0122)

C0582    

x055 OH5 MCTRL Temperature inside the controller > C0124 C0605    

x057 OH7 MCTRL Motor temperature higher than variable limit

temperature (C0121)

C0584    

x058 OH8 MCTRL Motor temperature via inputs T1/T2 too high C0585     

x061 CE0 AIF Communication error between AIF

modulePLC

C0126      

CAN communication error:

x062 CE1 CAN1 CAN1_IN (monitoring time can be set under

C0357/1)

C0591

     

x063 CE2 CAN2 CAN2_IN (monitoring time can be set under

C0357/2)

C0592

x064 CE3 CAN3 CAN3_IN (monitoring time can be set under

C0357/3)

C0593

x065 CE4 CAN CAN BUS−OFF status

(too many faulty telegrams received)

C0595      

x066 CE5 CAN CAN time−out (gateway function C0370) C0603      

x070 U15 internal Undervoltage of internal 15 V voltage supply    

x071 CCr internal Internal error

   

x072 PR1 internal Check sum error in parameter set 1    

x074 PEr internal Program error

   

x075 PR0 internal General error in the parameter sets

   

x076 PR5 internal Error saving parameters   

x079 PI internal Error during parameter initialisation

   

x080 PR6 internal Too many user codes    

x082 Sd2 MCTRL Resolver error C0586     

x083 Sd3 MCTRL Encoder error at X9 PIN 8 C0587    

x085 Sd5 MCTRL Encoder error at analog input (X6) (C0034 = 1) C0598     

x086 Sd6 MCTRL Sensor error: motor temperature (X7 or X8) C0594     

x087 Sd7 MCTRL Absolute−value encoder error at X8

C0025   

x088 Sd8 MCTRL Absolute−value encoder error at X8

C0580    

x: 0 = TRIP, 1 = Message, 2 = Warning, 3 = FAIL−QSP

After error correction: completely deenergise the device!

1 2 ... 108 109 110 111 112 113 114 115 116 117 118 ... 168 169

Komentáře k této Příručce

Žádné komentáře

Lenze DDS Target 9300 Servo PLC V8.x Uživatelský manuál Strana 113

Komentáře k této Příručce

Související produkty a manuály pro Hardware Lenze DDS Target 9300 Servo PLC V8.x