Lenze DDS Target 9300 Servo PLC V8.x Uživatelský manuál stáhnout pdf (Strana 118)

9300 Servo PLC

Appendix

3−112

9300 Servo PLC EN 5.1

Fault message RemedyCauseDescription

No.

RemedyCauseDescription

Display

x058 OH8 Motor temperature via inputs T1 and T2 is

too high.

Motor is thermally overloaded due to:

 Impermissible continuous current

 Frequent or too long acceleration

processes

 Check drive dimensioning.

 Switch off monitoring (C0585 = 3).

Terminals T1 and T2 are not connected Connect PTC/temperature contact.

x061 CE0 Automation interface (AIF) communication

error

Faulty transfer of control commands via AIF.  Plug in the communication

module/keypad XT firmly, screw down, if

necessary.

 Switch off monitoring (C0126 = 3).

x062 CE1 Communication error on the process data

input object CAN1_IN

CAN1_IN object receives faulty data or

communication is interrupted.

 Check wiring at X4.

 Check sender.

 Increase monitoring time under

C0357/1, if necessary.

 Switch off monitoring (C0591 = 3).

x063 CE2 Communication error on the process data

input object CAN2_IN

CAN2_IN object receives faulty data or

communication is interrupted.

 Check wiring at X4.

 Check sender.

 Increase monitoring time under

C0357/2, if necessary.

 Switch off monitoring (C0592 = 3).

x064 CE3 Communication error on the process data

input object CAN3_IN

CAN3_IN object receives faulty data or

communication is interrupted.

 Check wiring at X4.

 Check sender.

 Increase monitoring time under

C0357/3, if necessary.

 Switch off monitoring (C0593 = 3).

x065 CE4 BUS−OFF state of system bus (CAN) The controller has received too many faulty

telegrams via the system bus (CAN) and has

disconnected from the bus.

 Check wiring at X4: Is the bus correctly

terminated?

 Check shield connection of the cables.

 Check PE connection.

 Check bus load, reduce the baud rate if

necessary. (Observe the cable length!)

 Switch off the monitoring (C0595 = 3).

x066 CE5 Time−out of system bus (CAN)

(communication error of gateway function)

For remote parameterisation (C0370,

C0371) via system bus (CAN):

 Slave does not respond.

 Communication monitoring time has

been exceeded.

 Check wiring of system bus (CAN).

 Check CAN bus configuration.

0070 U15 Undervoltage of internal 15 V voltage supply Check voltage supply.

0071 CCr System failure

Strong interference injection on the control

cables

Screen control cables

Ground or earth loops in the wiring  Check wiring

 Check PE connection

After troubleshooting: Deenergise the

device completely (disconnect 24 V

supply, discharge DC bus)!

0072 PR1 Checksum error in parameter set 1

CAUTION: The Lenze setting is loaded

automatically!

 Fault when loading a parameter set.

 Interruption while transmitting the

parameter set via keypad.

 Set the required parameters and store

them under C0003 = 1.

 As to PLC devices, check the use of

pointers.

The stored parameters are incompatible

with the loaded software version.

Store the parameter set under C0003 = 1

first to allow for a faults reset.

0074 PEr Program error Error in the program flow Send the parameter set (on floppy

disk/CD−ROM) with a detailed description of

the problem to Lenze.

After troubleshooting: Deenergise the

device completely (disconnect 24 V

supply, discharge DC bus)!

0075 PR0 Error in parameter set.

The operating system software has been

updated.

Storage of the Lenze setting C0003 = 1.

After troubleshooting: Deenergise the

device completely (disconnect 24 V

supply, discharge DC bus)!

x: 0 = TRIP, 1 = Message, 2 = Warning, 3 = FAIL−QSP

1 2 ... 113 114 115 116 117 118 119 120 121 122 123 ... 168 169

Komentáře k této Příručce

Žádné komentáře

Lenze DDS Target 9300 Servo PLC V8.x Uživatelský manuál Strana 118

Komentáře k této Příručce

Související produkty a manuály pro Hardware Lenze DDS Target 9300 Servo PLC V8.x